Claytool Studio Open ClayForm →

Introducing ClayForm, the first tool from Claytool Studio.

Free tar paper templates for any pot you draw.

Draw one side of a vase, mug or bowl, see it in 3D, and print slab-building templates at the size you want.

Start designing in ClayForm Free. Runs in your browser, nothing to install.
claytool.studio
The ClayForm editor: a pot profile on the left, the 3D vessel beside it, and three printable templates along the bottom
A screenshot of ClayForm: the profile, the 3D preview and all three templates on one screen.
1

Draw the profile

Drag a few points to shape one side of the pot. Add curves, or trace over a photo of a form you like.

2

See it in 3D

The vessel updates as you draw, so you can judge the proportions before you touch any clay.

3

Print and build

Type the height or width you want, press Print, and cut your slabs from the sheets.

From image to real pot

Trace an image. Make it real.

Start from a photograph, a sketch or an AI image. ClayForm turns it into a template you can print, cut out and build from.

  1. An AI-generated image of a terracotta-red pour-over coffee dripper with a palm leaf design, on a tiled plinth at dusk

    1Start with a photograph

    A photograph of any pot you like, side on. A sketch or an AI image works too: this pour-over is not real, an AI image generator made it.

  2. The picture loaded into ClayForm with a straight line traced down the side of the cone between two points

    2Trace one side

    Load the picture into ClayForm and put one point at the foot and one at the rim. A cone needs only those two.

  3. The traced line shown as a 3D cone, wide at the top and narrow at the base

    3Check it in 3D

    ClayForm spins your line into the whole form, so you can check the shape before you cut anything.

  4. The cone flattened into a wide arch-shaped template

    4Get the flat template

    The cone opens out into one flat piece, called a cone frustum. That is the shape you cut from the slab.

  5. The Print preview showing the arch-shaped template split across two sheets by a dashed line

    5Print it full size

    Type the size you want and tick clay shrinkage, so the pot fires to that size. This one is the size of a standard dripper and fits on two sheets.

  6. The printed paper template lying on a sheet of black tar paper, with a silver pencil line drawn round it

    6Trace onto tar paper

    Tape the sheets together and cut out the paper shape. Draw round it on tar paper and cut that out. Now you have a template that survives wet clay.

  7. The pour-over dripper just built in wet grey clay, with its handle and foot attached, on a work board
    Just built, still wet
    The same handbuilt pour-over dripper finished in matte white, on a studio table
    Finished

    7Build it in clay

    Lay the tar paper on your slab and cut round it. Roll the slab into the cone and join the seam. The handle and foot are added by hand.

    These two are photos of the real pot, not AI.

Try it with your own image

Made with ClayForm

From a flat template to this.

This vase started as seven points in ClayForm. One side of the pot is all you draw; the tool spins it into the full form, then flattens it into templates to print and build from slabs.

ClayForm gave this vase its shape. The spikes and the surface were done by hand.

Design your own
The vase's profile in the ClayForm 2D editor: seven points forming a gentle barrel curve beside the centre line
The profile in ClayForm
A tall barrel-shaped white vase studded with dark clay spikes, on a stone plinth
The finished pot

Image trace

Copy a pot you love.

Seen a form you want to make? Put a photo of it behind the drawing and trace its edge. The tool turns your tracing into the same printable templates.

  • Drop in a photo, paste one from the clipboard, or link to it.
  • Fade it, move it and resize it until it lines up with the centre line.
  • Drag the points along one side of the pot. One side is all the tool needs.
Trace a pot

Cone frustum

Every pot is a stack of cones.

A cone frustum is a cone with its top sliced off: a ring with a sloping wall. Lay one flat and it becomes a curved band you can cut from a slab and wrap back into a ring.

Split your profile into stages and each stage becomes its own band. Flare out for the belly, lean in for the shoulder, rise for the neck. Build the rings, stack them, blend the joins, and a handful of simple shapes turns into a pot with real curves.

More stages follow the curve more closely, and fewer are quicker to build.

Three slab templates from one profile

Each template is made from the same profile and exports as an SVG file drawn to your measurements. It works for straight sides or curves, a mug or a tall vase.

Star radial

The base with every wall panel attached, in one piece.

Picket fence

Wall strips side by side, ready to join edge to edge.

Cone frustum

Each horizontal band unrolled into a single curved strip.

Settings you can change

Every template redraws the moment you change a setting.

2 stages8 stages
1 to 40

Stages

How many bands the pot is built from, bottom to top. More stages follow the curve more closely.

3 radials12 radials
3 to 12

Radials

How many panels go around the pot: the petals of the star and the strips of the picket fence.

small baselarge base
in, cm, mm

Your size

Type the height or the width you want, in inches, centimetres or millimetres, and every template is drawn to match. A template bigger than one sheet is split across pages when you print: how printing works.

Printing a template bigger than one sheet

Press Print in the tool and pick your paper. A small pot fits on one page. A bigger one is split across as many sheets as it needs, at 100% size, ready to tape together.

Questions potters ask

Short answers about slab templates and what ClayForm does and doesn't do.

What is ClayForm?

ClayForm is a free web tool that makes printable templates for slab-built (handbuilt) pottery. You draw one side of a pot, it shows the form in 3D, and it flattens that form into templates you print, cut out and use to cut your clay slabs.

What is a tar paper template?

Tar paper, also called roofing felt, is waterproof and can be reused many times, so potters cut their templates from it, lay them on a clay slab and cut around them. ClayForm makes the paper pattern at the size you ask for; you trace it onto tar paper.

How do I make a template for a slab-built vase, mug or bowl?

Open ClayForm, drag the points to draw one side of the pot, and type the height or the width you want. Pick a template type, press Print, and cut the printed sheets out. A straight-sided mug needs two points; a curvier vase needs a few more.

Which template type should I use?

Star Radial gives the base with every wall panel attached, in one piece. Picket Fence gives the wall panels as separate upright strips, plus the base. Cone Frustum splits the pot into stacked stages, each one a curved band that wraps into a ring. All three are made from the same drawing, so you can look at each before you print.

Can I print a template that is bigger than one sheet of paper?

Yes. ClayForm prints at 100% and splits a large template across as many sheets as it needs, on A4, US Letter, A3 or Tabloid paper. Each sheet has a trim edge, a line showing where the next sheet joins, and a sheet number, so the pieces tape together in order.

How do I know it printed at the right size?

Every printed sheet carries a short bar marked 2 inches or 50 millimetres. Measure it with a ruler before you cut. In your printer's window, keep the scale at 100% or 'actual size' and turn off 'fit to page'.

Can I copy the shape of a pot I already like?

Yes. Load a photo of the pot behind the drawing, by dropping it in, pasting it or giving a link, then fade it and drag the points along one edge of the pot. ClayForm builds the templates from your tracing.

Does ClayForm allow for clay shrinkage?

Yes. In the Print window, tick 'Allow for clay shrinkage' and enter your clay's shrinkage percentage. ClayForm then prints the templates bigger by the right amount, so the pot comes out at the size you typed after its final firing. Use the clay's total shrinkage, from wet to final firing, which is usually printed on the bag or given on the maker's website. With the box unticked, the templates come out at exactly the size you typed.

Does ClayForm allow for slab thickness?

No. The templates describe the surface of the form and do not add anything for the thickness of the slab or for bevelled joins.

Do curved profiles work?

Star Radial, Picket Fence and the 3D view follow curves. Cone Frustum does not: each stage has a straight wall between two points, so the tool marks that template red when the drawing has a curve in it. Adding more stages lets the straight walls follow a curve more closely.

How many sides and stages can a pot have?

From 3 to 12 sides around, and from 1 to 40 stages from base to rim. Sizes can be entered in inches, centimetres or millimetres.

Can I use the templates with a cutting machine or a drawing program?

Each template can be downloaded as a standard SVG file drawn at its true size, which vector drawing programs and cutting-machine software can open.

Is ClayForm free, and do I need an account?

It is free and needs no account or installation. It runs in the web browser on a computer, tablet or phone. Your design stays in your browser; the Save button keeps a copy as a file on your own device.

Who makes ClayForm?

ClayForm is made by Mark, a potter who mainly handbuilds, and is the first tool from Claytool Studio. Bug reports and ideas can be sent with the Feedback button in the tool or the message form on the site.

Mark, the maker of ClayForm, at a pottery wheel trimming a small bowl

About me

Hi, I'm Mark.

I mainly handbuild ceramics these days, and I built ClayForm for my own studio work, so I could draw a shape, print the templates and cut the slabs without guessing at angles or wasting clay.

It's free to use and I keep improving it as I build with it. If you make something from one of these templates, or something doesn't work, tell me.

ClayForm is the first tool from Claytool Studio. More are on the way.

Like it? Say so.

It costs nothing and it makes one potter unreasonably happy. Or tell me what's broken, what's missing, or what you made.